Mazda 3 Service Manual: Front Door Key Cylinder RemovalInstallation

Mazda 3 Service Manual: Front Door Key Cylinder Removal/Installation

1. To access the glass installation bolt, position the front door glass so that the distance from the top of the front door glass to the upper part of the front beltline molding isapprox. 80 mm {3.1 in}

.


2. Disconnect the negative battery cable..

3. Remove the following parts:

a. Inner garnish.

b. Front door trim.

c. Front door speaker.

d. Front door glass.

e. Front door module panel.

4. Remove the service hole cover.


5. Remove the tab, then remove the door lock-link bracket.


6. Remove the service hole cover.


7. Remove the screw from the service hole.

NOTE:

  • The screw cannot be removed because of the stopper.


8. Lift the clip in the direction of the arrow (1), and pull out the key rod in the direction of the arrow (2).


9. Press the tab on the front outer handle bracket in the direction of the arrow.


10. Maintaining the condition in Step 9, remove the front key cylinder.


11. Using a tape-wrapped fastener remover, press up the collar cap in the direction of the arrow shown in the arrow, press aside the front door key cylinder tabs (1), and remove the collar cover from the front door key cylinder.


12. Install in the reverse order of removal.

Other materials:

Headlight Auto Leveling System Initialization
CAUTION: If the headlight auto leveling initial setting is not stored correctly, the headlight auto leveling system may not operate normally. To store the initial setting correctly, perform the initial setting with the vehicle under the following conditions: No occupant ...

Storage Compartments
WARNING Keep storage boxes closed when driving: Driving with the storage boxes open is dangerous. To reduce the possibility of injury in an accident or a sudden stop, keep the storage boxes closed when driving. Do not put articles in storage spaces with no lid: ...

Oil Pump Removal/Installation [Skyactiv G 2.0]
WARNING: Hot engines and engine oil can cause severe burns. Turn off the engine and wait until it and the engine oil have cooled. A vehicle that is lifted but not securely supported on safety stands is dangerous. It can slip or fall, causing death or serious injury.

Related news

  • Hyundai Elantra: Repair procedures (A4CF2)
  • Nissan Rogue Owners Manual: Appearance and care
  • Chrysler 200: To Disarm The System
  • Mazda 3 Service Manual: Ignition Key Illumination RemovalInstallation
  • Toyota RAV4 Service Manual: Catalyst system efficiency below threshold (bank 1)

  • Mazda 3 Service Manual: Front Door Key Cylinder RemovalInstallation

    Mazda 3 Service Manual: Front Door Key Cylinder RemovalInstallation

    Mazda 3 Service Manual: Front Door Key Cylinder RemovalInstallation

    Mazda 3 Service Manual: Front Door Key Cylinder RemovalInstallation

    Mazda 3 Service Manual: Front Door Key Cylinder RemovalInstallation

    Mazda 3 Service Manual: Front Door Key Cylinder RemovalInstallation

    Mazda 3 Service Manual: Front Door Key Cylinder RemovalInstallation

    Mazda 3 Service Manual: Front Door Key Cylinder RemovalInstallation

    Mazda 3 Service Manual: Front Door Key Cylinder RemovalInstallation

    Mazda 3 Service Manual: Front Door Key Cylinder RemovalInstallation

    Mazda 3 Service Manual: Front Door Key Cylinder RemovalInstallation

    Mazda 3 Service Manual: Front Door Key Cylinder RemovalInstallation

    Mazda 3 Service Manual: Front Door Key Cylinder RemovalInstallation

    Mazda 3 Service Manual: Front Door Key Cylinder RemovalInstallation

    Mazda 3 Service Manual: Front Door Key Cylinder RemovalInstallation

    Mazda 3 Service Manual: Front Door Key Cylinder RemovalInstallation

    Mazda 3 Service Manual: Front Door Key Cylinder RemovalInstallation

    Mazda 3 Service Manual: Front Door Key Cylinder RemovalInstallation

    Mazda 3 Service Manual: Front Door Key Cylinder RemovalInstallation

    Mazda 3 Service Manual: Front Door Key Cylinder RemovalInstallation