Toyota Sienna Service Manual: Shift Solenoid D Control Circuit

Toyota Sienna Service Manual: Shift Solenoid "D" Control Circuit

Shift Solenoid "D" Control Circuit

DESCRIPTION

Shifting from 1st to 5th is performed in combination with "ON" and "OFF" operation of the shift solenoid valves SL1, SL2, SL3, S4 and SR which are controlled by the ECM. If an open or short circuit occurs in either of the shift solenoid valves, the ECM controls the remaining normal shift solenoid valves to allow the vehicle to be operated smoothly (Fail safe function).

MONITOR DESCRIPTION

The ECM commands gear shifts by turning the shift solenoid valves "ON/OFF". When there is an open or short circuit in any shift solenoid valve circuit, the ECM detects the problem and illuminates the MIL and stores the DTC. And the ECM performs the fail-safe function and turns the other normal shift solenoid valves "ON/OFF" (In case of an open or short circuit, the ECM stops sending current to the circuit.) (See page AX-30).

MONITOR STRATEGY

TYPICAL ENABLING CONDITIONS

TYPICAL ENABLING CONDITIONS

TYPICAL MALFUNCTION THRESHOLDS

TYPICAL MALFUNCTION THRESHOLDS

COMPONENT OPERATING RANGE

WIRING DIAGRAM

WIRING DIAGRAM

INSPECTION PROCEDURE

1 INSPECT TRANSMISSION WIRE (S4)

INSPECT TRANSMISSION WIRE (S4)

(a) Disconnect the transmission wire connector from the transaxle.

(b) Measure the resistance according to the value(s) in the table below.

Standard resistance

2 CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

(a) Connect the transmission wire connector to the transaxle.

(b) Disconnect the connector from the ECM.

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance

REPLACE ECM

3 INSPECT SHIFT SOLENOID VALVE S4

INSPECT SHIFT SOLENOID VALVE S4

(a) Remove the shift solenoid valve S4.

(b) Measure the resistance according to the value(s) in the table below.

Standard resistance

(c) Connect the positive (+) lead to the terminal of the solenoid connector, and the negative (-) lead to the solenoid body.

OK: The solenoid makes an operating sound.

Related news

  • Honda Accord: General Information
  • Automatic transmission fluid
  • Chevrolet Sonic Repair Manual: Heater Core Outlet Tube Replacement
  • Mazda 3 Service Manual: Instrument Cluster Configuration
  • Nissan Sentra Service Manual: Rear shock absorber

  • Toyota Sienna Service Manual: Shift Solenoid D Control Circuit

    Toyota Sienna Service Manual: Shift Solenoid D Control Circuit

    Toyota Sienna Service Manual: Shift Solenoid D Control Circuit

    Toyota Sienna Service Manual: Shift Solenoid D Control Circuit

    Toyota Sienna Service Manual: Shift Solenoid D Control Circuit

    Toyota Sienna Service Manual: Shift Solenoid D Control Circuit

    Toyota Sienna Service Manual: Shift Solenoid D Control Circuit

    Toyota Sienna Service Manual: Shift Solenoid D Control Circuit

    Toyota Sienna Service Manual: Shift Solenoid D Control Circuit

    Toyota Sienna Service Manual: Shift Solenoid D Control Circuit

    Toyota Sienna Service Manual: Shift Solenoid D Control Circuit

    Toyota Sienna Service Manual: Shift Solenoid D Control Circuit

    Toyota Sienna Service Manual: Shift Solenoid D Control Circuit

    Toyota Sienna Service Manual: Shift Solenoid D Control Circuit

    Toyota Sienna Service Manual: Shift Solenoid D Control Circuit

    Toyota Sienna Service Manual: Shift Solenoid D Control Circuit

    Toyota Sienna Service Manual: Shift Solenoid D Control Circuit

    Toyota Sienna Service Manual: Shift Solenoid D Control Circuit

    Toyota Sienna Service Manual: Shift Solenoid D Control Circuit

    Toyota Sienna Service Manual: Shift Solenoid D Control Circuit

    Toyota Sienna Service Manual: Shift Solenoid D Control Circuit

    Toyota Sienna Service Manual: Shift Solenoid D Control Circuit

    Toyota Sienna Service Manual: Shift Solenoid D Control Circuit

    Toyota Sienna Service Manual: Shift Solenoid D Control Circuit