Toyota Sienna Service Manual: Short to B in Front Passenger Side Squib Circuit

Toyota Sienna Service Manual: Short to B+ in Front Passenger Side Squib Circuit

DTC B0108/52 Short to B+ in Front Passenger Side Squib Circuit

DESCRIPTION

The front passenger side squib circuit consists of the center airbag sensor assembly and the front passenger airbag assembly.

The circuit instructs the SRS to deploy when deployment conditions are met.

DTC B0108/52 is recorded when a short to B+ is detected in the front passenger side squib circuit

DTC No.

DTC Detecting Condition

Trouble Area

B0108/52

  • Short circuit in front passenger side squib wire harness (to B+)
  • Front passenger side squib malfunction
  • Center airbag sensor assembly malfunction
  • Front passenger airbag assembly (Front passenger side squib)
  • Center airbag sensor assembly
  • Instrument panel wire

INSPECTION PROCEDURE

HINT:

  •  Perform the simulation method by selecting the "check mode" (signal check) with the intelligent tester (8).
  •  After selecting the "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road

1 CHECK FRONT PASSENGER AIRBAG ASSEMBLY (FRONT PASSENGER SIDE SQUIB)

CHECK FRONT PASSENGER AIRBAG ASSEMBLY (FRONT PASSENGER SIDE SQUIB)

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Disconnect the connectors from the front passenger airbag assembly.
  4.  Connect the black wire side of SST (resistance 2.1 Ω) to the instrument panel wire.

CAUTION: Never connect a tester to the front passenger airbag assembly (front passenger side squib) for measurement, as this may lead to a serious injury due to airbag deployment.

NOTICE: Do not forcibly insert the SST into the terminals of the connector when connecting.

Insert the SST straight into the terminals of the connector.

SST 09843-18060

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  2.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  3.  Clear the DTCs stored in memory (5).
  4.  Turn the ignition switch to the LOCK position.
  5.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  6.  Check the DTCs (5).

OK: DTC B0108/52 is not output. HINT: Codes other than DTC B0108/52 may be output at this time, but they are not related to this check.

Go to step 2

REPLACE FRONT PASSENGER AIRBAG ASSEMBLY

2 CHECK INSTRUMENT PANEL WIRE (FRONT PASSENGER SIDE SQUIB CIRCUIT)

CHECK INSTRUMENT PANEL WIRE (FRONT PASSENGER SIDE SQUIB CIRCUIT)

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Disconnect the SST (resistance 2.1 Ω) from the instrument panel wire.
  4.  Disconnect the connector from the center airbag sensor assembly.
  5.  Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  6.  Turn the ignition switch to the ON position.
  7.  Measure the voltage according to the value(s) in the table below.

Standard voltage

Standard voltage

REPAIR OR REPLACE INSTRUMENT PANEL WIRE

3 CHECK CENTER AIRBAG SENSOR ASSEMBLY

CHECK CENTER AIRBAG SENSOR ASSEMBLY

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Connect the connectors to the front passenger airbag assembly and the center airbag sensor assembly.
  4.  Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  5.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  6.  Clear the DTCs stored in memory (5).
  7.  Turn the ignition switch to the LOCK position.
  8.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  9.  Check the DTCs (5).

OK: DTC B0108/52 is not output. HINT: Codes other than code B0108/52 may be output at this time, but they are not related to this check

REPLACE CENTER AIRBAG SENSOR ASSEMBLY

USE SIMULATION METHOD TO CHECK

Short in Side Squib RH Circuit
DTC B0110/43 Short in Side Squib RH Circuit DESCRIPTION The side squib RH circuit consists of the center airbag sensor assembly and the front seat side airbag assembly RH. The circuit instruct ...
Other materials:

Low Battery Positive Voltage
DTC C1241/41 Low Battery Positive Voltage DESCRIPTION WIRING DIAGRAM INSPECTION PROCEDURE 1 INSPECT ECU-IG FUSE (a) Remove the ECU-IG fuse from the driver side J/B. (b) Check continuity of the ECU-IG fuse. Standard resistance 2 CHECK BATTERY (a) Check the positive battery volt ...

CD cannot be Ejected
INSPECTION PROCEDURE 1 PRESS "EJECT" AND CHECK OPERATION Press the CD EJECT switch of the radio receiver for 2 seconds or more and check that the CD is ejected. OK: CD is ejected 2 REPLACE CD WITH ANOTHER AND RECHECK Insert another CD and check if it is ejected. OK: CD ...

Removal
1. PRECAUTION CAUTION: Be sure to read "PRECAUTION" thoroughly before servicing. 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL CAUTION: Wait for 90 seconds after disconnecting the cable to prevent the airbag working. 3.

Related news

  • Toyota Tacoma 2015-2018 Service Manual: Fuel Injector(for Direct Injection)
  • Mazda 3 Service Manual: Discharge Headlight Service Warnings
  • Toyota RAV4 Service Manual: Transmission range sensor circuit malfunction (prndl input)
  • Kia Soul: Remote control
  • Nissan Sentra Service Manual: Service data and specifications (SDS)

  • Toyota Sienna Service Manual: Short to B in Front Passenger Side Squib Circuit

    Toyota Sienna Service Manual: Short to B in Front Passenger Side Squib Circuit

    Toyota Sienna Service Manual: Short to B in Front Passenger Side Squib Circuit

    Toyota Sienna Service Manual: Short to B in Front Passenger Side Squib Circuit

    Toyota Sienna Service Manual: Short to B in Front Passenger Side Squib Circuit

    Toyota Sienna Service Manual: Short to B in Front Passenger Side Squib Circuit

    Toyota Sienna Service Manual: Short to B in Front Passenger Side Squib Circuit

    Toyota Sienna Service Manual: Short to B in Front Passenger Side Squib Circuit

    Toyota Sienna Service Manual: Short to B in Front Passenger Side Squib Circuit

    Toyota Sienna Service Manual: Short to B in Front Passenger Side Squib Circuit

    Toyota Sienna Service Manual: Short to B in Front Passenger Side Squib Circuit

    Toyota Sienna Service Manual: Short to B in Front Passenger Side Squib Circuit

    Toyota Sienna Service Manual: Short to B in Front Passenger Side Squib Circuit

    Toyota Sienna Service Manual: Short to B in Front Passenger Side Squib Circuit

    Toyota Sienna Service Manual: Short to B in Front Passenger Side Squib Circuit

    Toyota Sienna Service Manual: Short to B in Front Passenger Side Squib Circuit

    Toyota Sienna Service Manual: Short to B in Front Passenger Side Squib Circuit

    Toyota Sienna Service Manual: Short to B in Front Passenger Side Squib Circuit

    Toyota Sienna Service Manual: Short to B in Front Passenger Side Squib Circuit

    Toyota Sienna Service Manual: Short to B in Front Passenger Side Squib Circuit