Toyota Sienna Service Manual: Short to GND in Front Pretensioner Squib LHCircuit

Toyota Sienna Service Manual: Short to GND in Front Pretensioner Squib LHCircuit

Toyota Sienna Service Manual: Short to GND in Front Pretensioner Squib LH Circuit

DTC B0137/71 Short to GND in Front Pretensioner Squib LH Circuit

DESCRIPTION

The front pretensioner squib LH circuit consists of the center airbag sensor assembly and the front seat outer belt assembly LH.

This circuit instructs the SRS to deploy when deployment conditions are met.

DTC B0137/71 is recorded when a short to ground is detected in the front pretensioner squib LH circuit.

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

HINT:

  •  Perform the simulation method by selecting the "check mode" (signal check) with the intelligent tester.
  •  After selecting the "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road

1 CHECK FRONT SEAT OUTER BELT ASSEMBLY LH (FRONT PRETENSIONER SQUIB LH)

CHECK FRONT SEAT OUTER BELT ASSEMBLY LH

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Disconnect the connectors from the front seat outer belt assembly LH.
  4.  Connect the white wire side of SST (resistance 2.1 Ω) to the floor wire.

CAUTION: Never connect a tester to the front seat outer belt assembly LH (front pretensioner squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.

NOTICE: Do not forcibly insert the SST into the terminals of the connector when connecting.

Insert the SST straight into the terminals of the connector.

SST 09843-18060

  1.  Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  2.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  3.  Clear the DTCs stored in memory.
  4.  Turn the ignition switch to the LOCK position.
  5.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  6.  Check the DTCs.

OK: DTC B0137/71 is not output.

HINT: Codes other than DTC B0137/71 may be output at this time, but they are not related to this check.

REPLACE FRONT SEAT OUTER BELT ASSEMBLY LH

2 FLOOR WIRE (FRONT PRETENSIONER SQUIB LH CIRCUIT)

FLOOR WIRE

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Disconnect the SST (resistance 2.1 Ω) from the floor wire.
  4. Disconnect the connector from the center airbag sensor assembly.
  5.  Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

3 CHECK CENTER AIRBAG SENSOR ASSEMBLY

CHECK CENTER AIRBAG SENSOR ASSEMBLY

  1. Connect the connectors to the front seat outer belt assembly LH and the center airbag sensor assembly.
  2.  Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  3.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  4.  Clear the DTCs stored in memory.
  5.  Turn the ignition switch to the LOCK position.
  6.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  7.  Check the DTCs.

OK: DTC B0137/71 is not output.

HINT: Codes other than DTC B0137/71 may be output at this time, but they are not related to this check.

USE SIMULATION METHOD TO CHECK

Other materials:

Diagnosis system
1. CHECK DLC3  The vehicle's ECU uses ISO 15765-4 for communication protocol. The terminal arrangement of the DLC3 complies with SAE J1962 and matches the ISO 15765-4 format. NOTICE: *: Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not ...

Unlocking and locking the doors from the inside
Door lock switch Locks all the doors Unlocks all the doors Inside lock button Locks the door Unlocks the door The front doors can be opened by pulling the inside handle even if the lock buttons are in the lock position. ...

Removal
1. REMOVE CENTER REAR SEAT LAP TYPE BELT ASSEMBLY (for 8-Passenger) HINT: Refer to the instructions for disassembly of the rear No. 1 seat assembly (for center seat).  Remove the bolt and center seat lap type belt assembly. 2. REMOVE CENTER REAR NO.

Related news

  • Kia Soul: Tilting the sunroof
  • Toyota Camry: Battery-saving function
  • Toyota Highlander Owners Manual: Front seats
  • Toyota Camry: Changing ENGINE START STOP switch modes
  • Mazda 3 Owners Manual: Seats

  • Toyota Sienna Service Manual: Short to GND in Front Pretensioner Squib LHCircuit

    Toyota Sienna Service Manual: Short to GND in Front Pretensioner Squib LHCircuit

    Toyota Sienna Service Manual: Short to GND in Front Pretensioner Squib LHCircuit

    Toyota Sienna Service Manual: Short to GND in Front Pretensioner Squib LHCircuit

    Toyota Sienna Service Manual: Short to GND in Front Pretensioner Squib LHCircuit

    Toyota Sienna Service Manual: Short to GND in Front Pretensioner Squib LHCircuit

    Toyota Sienna Service Manual: Short to GND in Front Pretensioner Squib LHCircuit

    Toyota Sienna Service Manual: Short to GND in Front Pretensioner Squib LHCircuit

    Toyota Sienna Service Manual: Short to GND in Front Pretensioner Squib LHCircuit

    Toyota Sienna Service Manual: Short to GND in Front Pretensioner Squib LHCircuit

    Toyota Sienna Service Manual: Short to GND in Front Pretensioner Squib LHCircuit

    Toyota Sienna Service Manual: Short to GND in Front Pretensioner Squib LHCircuit

    Toyota Sienna Service Manual: Short to GND in Front Pretensioner Squib LHCircuit

    Toyota Sienna Service Manual: Short to GND in Front Pretensioner Squib LHCircuit

    Toyota Sienna Service Manual: Short to GND in Front Pretensioner Squib LHCircuit

    Toyota Sienna Service Manual: Short to GND in Front Pretensioner Squib LHCircuit

    Toyota Sienna Service Manual: Short to GND in Front Pretensioner Squib LHCircuit

    Toyota Sienna Service Manual: Short to GND in Front Pretensioner Squib LHCircuit

    Toyota Sienna Service Manual: Short to GND in Front Pretensioner Squib LHCircuit

    Toyota Sienna Service Manual: Short to GND in Front Pretensioner Squib LHCircuit

    Toyota Sienna Service Manual: Short to GND in Front Pretensioner Squib LHCircuit

    Toyota Sienna Service Manual: Short to GND in Front Pretensioner Squib LHCircuit

    Toyota Sienna Service Manual: Short to GND in Front Pretensioner Squib LHCircuit

    Toyota Sienna Service Manual: Short to GND in Front Pretensioner Squib LHCircuit

    Toyota Sienna Service Manual: Short to GND in Front Pretensioner Squib LHCircuit

    Toyota Sienna Service Manual: Short to GND in Front Pretensioner Squib LHCircuit

    Toyota Sienna Service Manual: Short to GND in Front Pretensioner Squib LHCircuit

    Toyota Sienna Service Manual: Short to GND in Front Pretensioner Squib LHCircuit